|
"Hands-On"
Programming for the SLC500™ Programmable Controller Using RSLogix500™ Software
Comprehensive 5-Day PLC
Training Seminar in a Combination "Hands-ON" and Classroom Session
NOTE:
While Allen-Bradley PLCs are used, course content will
apply to users of all PLCs.
Length:
5 Days (Classes start at 8:00 a.m. and finish
at 4:00 p.m.)
Seminar Purpose:
The purpose of this seminar is to provide you
with the skills needed to organize, plan, write, enter, test, and document
SLC500™ programs using
the basic programming instructions and RSLogix500™ software. You will learn to
use specific advanced instructions. You will learn to edit, upload, download,
save, and restore as well as program specific ladder logic instructions. The
instructor will demonstrate the use of bit-level, timer, counter, conversion,
math, comparison, data manipulation, program control, and diagnostic
instructions in detail, then provide realistic situations that allow you to
practice using these instructions.
Frequent hands-on practice is
provided using an actual SLC500™ system workstation.
Seminar Objectives:
Upon completion of this seminar, you will be able to
produce SLC500™ programs using RSLogix500™ software by performing these
actions:
- Write and edit programs
- Enter and test programs
- Document and
maintain programs
Hands-On Training:
These Seminars offer real Hands-On Training, not just a
demonstration. You will spend approximately 50% of your time actually working
with Programmable Controllers, either individually or with a partner. Your team
size will never exceed two Participants. Each team will be assigned a Training
Center, consisting of a Personal Computer with RSLogix500™ Programming Software
and an Allen-Bradley SLC500™ Programmable Logic Controller for their exclusive
use.
Who Should Attend:
Individuals who need to be able to write
ladder logic programs for a SLC500™ processor using RSLogix500™ software should
attend this seminar.
Prerequisites:
The following prerequisites are required.
- Completion of
the Operation, Installation, Maintenance and
Troubleshooting of SLC500™ Programmable Controllers Using RSLogix500™ Software seminar or equivalent knowledge.
- Working knowledge of basic
controls and electrical principles
Topical Outline:
- Connecting The Programming Terminal
- Managing And
Entering Program Files
- Storing Project Files
- Using EEPROM
Transfer
- Organizing The Data Table
- Using The Data Monitor
Function
- Writing, Entering, And Editing Ladder Logic
- Entering And Editing
Descriptions And Symbolic Addresses
- Searching Through The Ladder
Logic
- Configuring And Printing Reports
- Define And Identify The Function Of
Internal Relay Instructions
- Operation Of The Latch And Unlatch
Instructions
- Convert Fundamental Relay Ladder Diagrams To PLC Logic Ladder
Programs
- Selecting And Programming Timer Instructions
- Differentiate
Between Non-Retentive And Retentive Timers
- Selecting And Programming Counter
Instructions
- Operating Principle Of A Transitional, Or One-Shot
Instruction
- Applying Immediate I/O Update Instructions
- Compare The
Operation Of Discrete I/Os With That Of Multi-Bit And Analog Types
- Selecting
And Programming Comparison Instructions
- Selecting And Programming Math
Instructions
- Selecting And Programming Conversion Instructions
- Selecting
And Programming Data Manipulation Instructions
- Selecting And Programming
Shift Register Instructions
- Selecting And Programming Sequencer
Instructions
- Selecting And Programming Control Instructions
- Identify And
Understand Jump Instructions
- Selecting And Programming Diagnostic
Instructions
- Configuring And Applying Fault Routines
Seminar Fee:
Contact William J. Dumas & Associates.
Open Training Seminar Schedule:
William J. Dumas & Associates has
entered into a contractural agreement with American Trainco, Inc. American
Trainco is authorized to market this seminar. Please contact ATI directly for
scheduled dates.
ATI contact information:
Contact: Dan Sciantarelli
Telephone: 877-978-7246
Web Site:
www.AmericanTrainco.com |